High-quality replacement kits are manufactured from hot-rolled ASTM 4115 and case-hardened to 58-62 Rc
Advanced design uses strategically located side scalloping and vent slots to minimize high rpm bearing race distortion
Rods are double-forged to improve grain flow and maintain dimensional consistency
Rods are also shot-peened and double-honed for superior strength under heavy loads
Small ends are double drilled to supply extra lubrication and cooling to the wrist pin bearing, which is especially important when the piston crown is close to the wrist pin bearing
Thrust washers and crank pin bearings are silver-coated for added lubricity
Kits sold complete with rod, crank pin, crank pin bearing, top end bearing and thrust washers
Part No. 56-894.HR / 56-894_HR (oro2u.com)
Technical Specifications: Big End Bearing (mm): 24x31x17 Big End Bore (mm): 31.00 Center-Center 132mm Big End Width (mm): 16.90
Cross Reference Numbers Only: 54630015044
KTM
1991 KTM 250 DXC
1990 KTM 250 DXC
1999 KTM 250 EXC
1998 KTM 250 EXC
1997 KTM 250 EXC
1996 KTM 250 EXC
1995 KTM 250 EXC
1994 KTM 250 EXC
1993 KTM 250 EXC
1992 KTM 250 EXC
1991 KTM 250 EXC
1990 KTM 250 EXC
1999 KTM 250 MXC
1998 KTM 250 MXC
1999 KTM 250 SX
1998 KTM 250 SX
1997 KTM 250 SX
1996 KTM 250 SX
1995 KTM 250 SX
1994 KTM 250 SX
1993 KTM 250 SX
1992 KTM 300 DXC
1991 KTM 300 DXC
1990 KTM 300 DXC
1999 KTM 300 EXC
1998 KTM 300 EXC
1997 KTM 300 EXC
1996 KTM 300 EXC
1995 KTM 300 EXC
1994 KTM 300 EXC
1993 KTM 300 EXC
1992 KTM 300 EXC
1991 KTM 300 EXC
1990 KTM 300 EXC
1991 KTM 300 MX
1990 KTM 300 MX
1999 KTM 300 MXC
1998 KTM 300 MXC
1997 KTM 300 MXC
1996 KTM 300 MXC
1995 KTM 300 MXC
1994 KTM 300 MXC
1993 KTM 300 MXC
1993 KTM 300 SX
1992 KTM 300 T/XC
1991 KTM 300 T/XC
Center To Center (mm): 132.00 Pin Diameter (mm): 24.00 Pin Length (mm): 59.90 Small End Bearing (mm): 18x22x20
High-quality replacement kits are manufactured from hot-rolled ASTM 4115 and case-hardened to 58-62 Rc
Advanced design uses strategically located side scalloping and vent slots to minimize high rpm bearing race distortion
Rods are double-forged to improve grain flow and maintain dimensional consistency
Rods are also shot-peened and double-honed for superior strength under heavy loads
Small ends are double drilled to supply extra lubrication and cooling to the wrist pin bearing, which is especially important when the piston crown is close to the wrist pin bearing
Thrust washers and crank pin bearings are silver-coated for added lubricity
Kits sold complete with rod, crank pin, crank pin bearing, top end bearing and thrust washers
Part No. 56-894.HR / 56-894_HR (oro2u.com)
Technical Specifications: Big End Bearing (mm): 24x31x17 Big End Bore (mm): 31.00 Center-Center 132mm Big End Width (mm): 16.90
Cross Reference Numbers Only: 54630015044
KTM
1991 KTM 250 DXC
1990 KTM 250 DXC
1999 KTM 250 EXC
1998 KTM 250 EXC
1997 KTM 250 EXC
1996 KTM 250 EXC
1995 KTM 250 EXC
1994 KTM 250 EXC
1993 KTM 250 EXC
1992 KTM 250 EXC
1991 KTM 250 EXC
1990 KTM 250 EXC
1999 KTM 250 MXC
1998 KTM 250 MXC
1999 KTM 250 SX
1998 KTM 250 SX
1997 KTM 250 SX
1996 KTM 250 SX
1995 KTM 250 SX
1994 KTM 250 SX
1993 KTM 250 SX
1992 KTM 300 DXC
1991 KTM 300 DXC
1990 KTM 300 DXC
1999 KTM 300 EXC
1998 KTM 300 EXC
1997 KTM 300 EXC
1996 KTM 300 EXC
1995 KTM 300 EXC
1994 KTM 300 EXC
1993 KTM 300 EXC
1992 KTM 300 EXC
1991 KTM 300 EXC
1990 KTM 300 EXC
1991 KTM 300 MX
1990 KTM 300 MX
1999 KTM 300 MXC
1998 KTM 300 MXC
1997 KTM 300 MXC
1996 KTM 300 MXC
1995 KTM 300 MXC
1994 KTM 300 MXC
1993 KTM 300 MXC
1993 KTM 300 SX
1992 KTM 300 T/XC
1991 KTM 300 T/XC
Center To Center (mm): 132.00 Pin Diameter (mm): 24.00 Pin Length (mm): 59.90 Small End Bearing (mm): 18x22x20
