11 In stockBack to Top
PLIERS FOR SPRING LINK CLIP, MOTION PRO 08-0230 masterlinks, MASTERLINK - Chain & Belt Tools - Specific Tools - Tools & Workshop
PRODUCT INFORMATION
| Brand | Motion Pro |
|---|---|
| Product Type | Chain Tools |
| Product Group | Workshop Equipment |
| Catalogue | ATV, DIRT, TOOLS |
DESCRIPTION
MASTERLINK PLIERS MOTION PRO 08-0230
- Designed to simplify installation and removal of clip-type master links
- One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip
Part No. 00-141.MP (oro2u.com)
Chain Press Tool Kit, 08-0066
MOTION PRO CHAIN PRESS TOOL 08-0066
This chain tool will press on the outer link plates of master links.
Fits size 520,525,530 and 532 chain only.
Before using apply a liberal amount of high quality grease on threads and the back of pad plates.
Usage: This tool is used to press on connecting link side plates. Desirable for newer type press fit
link side plates which cannot be installed by hand.
Other tools recommended by Motion Pro for complete chain repair.
1. # 08-0230 (master link pliers)for master link clips.
General Instructions
1. Thread handle onto main press body
2. Install grooved pad plate into bottom of main body (stationary side)
2. Install the pad plate with two holes into the upper side of the press tool (Side with movable
hollow bolt ). At this time your plates should oppose each other so the plate with two
holes can allow the master link pins to move into the holes freely.
3. Install chain onto vehicle. Merge chain onto rear sprocket so you have a platform in
which to use the Chain Press Tool (it’s not necessary but makes installation easier).
4. Install connecting link from the inside of the sprocket. Insert the link so the pins
are pushed all the way through. And lightly install connecting link plate. Do not
forget to install any O-rings (if you have an O-ring chain) prior to installing the
plate.
5. Now , slowly screw the body bolt (hollow bolt) with the pad that has two holes down
on to the press fit plate until the plate is seated against the chain face and the link
fitment is snug. Caution!! Do not over tighten chain link for it will create binding and may
cause chain wear.
6. After connecting link plate is installed to the link. Use Motion Pro master link pliers for clip type master links to install the clip. The open end of the clip always faces away from the drive direction. Or use the Motion Pro chain riveting tool #08-0058 to stake the master link
plate into place.
MASTERLINK PLIERS MOTION PRO 08-0230
- Designed to simplify installation and removal of clip-type master links
- One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip
Part No. 00-141.MP (oro2u.com)
Chain Press Tool Kit, 08-0066
MOTION PRO CHAIN PRESS TOOL 08-0066
This chain tool will press on the outer link plates of master links.
Fits size 520,525,530 and 532 chain only.
Before using apply a liberal amount of high quality grease on threads and the back of pad plates.
Usage: This tool is used to press on connecting link side plates. Desirable for newer type press fit
link side plates which cannot be installed by hand.
Other tools recommended by Motion Pro for complete chain repair.
1. # 08-0230 (master link pliers)for master link clips.
General Instructions
1. Thread handle onto main press body
2. Install grooved pad plate into bottom of main body (stationary side)
2. Install the pad plate with two holes into the upper side of the press tool (Side with movable
hollow bolt ). At this time your plates should oppose each other so the plate with two
holes can allow the master link pins to move into the holes freely.
3. Install chain onto vehicle. Merge chain onto rear sprocket so you have a platform in
which to use the Chain Press Tool (it’s not necessary but makes installation easier).
4. Install connecting link from the inside of the sprocket. Insert the link so the pins
are pushed all the way through. And lightly install connecting link plate. Do not
forget to install any O-rings (if you have an O-ring chain) prior to installing the
plate.
5. Now , slowly screw the body bolt (hollow bolt) with the pad that has two holes down
on to the press fit plate until the plate is seated against the chain face and the link
fitment is snug. Caution!! Do not over tighten chain link for it will create binding and may
cause chain wear.
6. After connecting link plate is installed to the link. Use Motion Pro master link pliers for clip type master links to install the clip. The open end of the clip always faces away from the drive direction. Or use the Motion Pro chain riveting tool #08-0058 to stake the master link
plate into place.
Motion Pro (USA)
Manufacture high quality motorcycle, ATV cables, tools and controls
Motion Pro (USA)
Manufacture high quality motorcycle, ATV cables, tools and controls
Spot Something Wrong?
Let us know.Click here
